HHV Solar develops technology, equipment for setting up production facility, inks deal with Canadian firm Seema Singh.
Bangalore: It’s rare that scientists in India develop new technologies and see them reach the marketplace, at least during their active career. The barriers are both cultural and scientific. For A.K. Barua, professor emeritus at the 130-year-old Indian Association for the Cultivation of Science in Kolkata, commercialization took long—32 years— but eventually it helped his industry partner HHV Solar Technologies Pvt. Ltd break into the international league where a handful of companies sell turnkey production lines for thin film solar cells.
A.K. Barua (left) with Prasanth Sakhamuri at HHV Solar’s manufacturing facility.
With the setting up of a 10MW demonstration production facility in Dabaspet, 50km from Bangalore, that will become operational in about three weeks, HHV Solar becomes the first Indian company to have developed the technology as well as the equipment for setting up a production facility for thin film solar photovoltaic (SPV) modules. At $12 million (around Rs54.7 crore) for the plant, HHV says it has cut the hardware cost from the prevailing rate for setting up such a unit of about $30 million. “That’s very competitive. High capital cost is a major factor in the adoption of thin film technology,” said Amol Kotwal, deputy director, energy and power system, South Asia, Middle East and North Africa, Frost and Sullivan (F&S). Only a few equipment suppliers operate in this space, led by Applied Materials Inc., headquartered in California, and Oerlikon Solar of Swiss industrial group Oerlikon. If domestic users take to HHV’s technology, the competition could get very tough for existing vendors, said Kotwal.
HHV has signed a deal with Solar Source Corp., a Canadian renewable energy holding company, to establish Canada’s first thin film amorphous silicon solar panel manufacturing plant. “We are in serious negotiations with some Indian companies and intend to close at least four deals very soon,” said Prasanth Sakhamuri, managing director of HHV Solar, a holding company of Hind High Vacuum Co. Pvt. Ltd. Solar technology is entering the third generation, but first-generation crystalline silicon solar cells dominate the market, accounting for 87.3% of the global 6.3 gigawatts of solar photovoltaic installations, according to F&S estimates for 2009. Thin solar cells constitute the second generation, where amorphous silicon leads the pack. The latter, though cheaper, lighter and flexible, is less efficient than crystalline cells. A global race is on to increase the efficiency of thin cells, from the present 6.75-7% to 10% and beyond. From its research stable, supported by the ministry of new and renewable energy, HHV plans to roll out modules with 8% efficiency within a year. Efficiency refers to the rate at which solar power is converted into usable energy.
Thin SPVs are just trickling into India. In February 2009, Moser Baer India Ltd started the first such line of 40MW capacity, set up by Applied Materials Inc. In October, KSK Surya Photovoltaic Venture signed up Applied Materials for a 150MW capacity thin film line in Hyderabad. “So far there was no market in India. Companies exported most of their modules. The solar mission has created the critical local demand,” said Madhu Atre, president of Applied Materials India. The feed-in tariff of Rs18.44/kWh under the National Solar Mission (NSM) is a definitive step forward, he adds. The feed-in tariff is a premium, cost-based compensation rate offered to producers of renewable energy. India’s SPV market had a capacity of 972MW in 2008, which is estimated to increase to 2,575MW in 2015, according to F&S. But this falls short of the NSM target of 20 gigawatts by 2020.
Barua, who is also chairman of research and development in NSM, says the targets are aggressive and difficult to achieve. “But that doesn’t mean we will not work towards it.” For a long time, India didn’t pay attention to solar technology, Barua said. His own lab, despite being an early starter, faced intermittent funding shortages. Crystalline silicon, with about 15% efficiency, has gained some market share but since temperatures in many parts of the country go very high, thin film is more suitable in those regions, he said. “Beyond a point, a one degree rise in temperature leads to half a percent drop in crystalline cell efficiency.”
At the core of Barua’s team’s work lies the “plasma enhanced chemical vapour deposition” technology, which is a method of depositing silicon on glass to turn it into an electricity-generating module. “It’s a proud moment for us to have completely indigenized the technology development as well as the equipment,” said C.S. Solanki, professor of energy science and engineering at the Indian Institute of Technology, Mumbai. He says it comes at the right time as this is the focus of the NSM. However, “unless the cost difference (between crystalline and thin film) is substantial, say $1 per watt, thin film adoption will be low,” he cautioned. The actual cost-benefit ratio, Sakhamuri said, is not efficiency dependent. “Thin film is 35% cheaper than crystalline. For a given 100W module, thin cells produce more power than crystalline as they react to a wider spectrum of sunlight.” The sleek shop floor, designed by the National Institute of Design in Ahmedabad, has been built to attract customers, said Sakhamuri. It’s working—from rice mill owners to jewellery exporters, everyone seems to be interested in solar power now, he said.
